Overview
Most of HGM’s products use SAE J1939 standard messages as their “native” protocol, usually at a 500 kb data rate.
Some versions of our controller software have menus under Network Setup / J1939 Messages which allows you to specifically enable and disable the various messages. In most cases, these messages will be disabled by default. Note that a reboot of the controller is often required after these messages have been enabled or disabled.
Protocol Specifics
Attached to this page is a DBC file for the commonly used messages, along with the tables below. Some things to be aware of:
-
All of the CAN arbitration ids used are 29 bit, not 11 bit, per J1939.
-
In the tables below, the last byte of the CAN id is set to “03”, which is the J1939 address for the first transmission control ECU.
If you change this address in the controller setup, you will have to adjust the address accordingly. -
In the attached DBC file, the last byte of the CAN id is marked as an "XX", indicating a wildcard.
If you have to hard code this number, use a "03", which is the J1939 address for the first transmission control ECU. -
The upper bits of a J1939 arbitration id are used for priority. In all cases, HGM uses the SAE recommended priority and that is shown in the tables below.
-
Not all signals and messages are transmitted for all transmission and engine type combinations.
EEC1, EEC2 and ET1 are sent from the engine address, in the engine’s stead, and are not enabled in the J1939 engine configurations. -
In J1939, an all ones bit combination is used to describe the "not available" situation, so if a bit field is all ones, then the system isn’t transmitting that signal.
-
For torque management, you will want to use the "shift in process" bits of ETC1.
Not all transmission types transmit this signal. -
Bytes are numbered 1-8, with 1 being the first byte in the CAN frame.
-
Bits are numbered 0 to 7, with 0 being the least significant bit in the byte.
-
To convert a signal: physical value = raw value × multiplier + offset. Multi-byte signals are little-endian (Intel byte order): the lower-numbered byte holds the least significant bits.
ETC1 Electronic Transmission
CAN ID 0x0CF00203 (29-bit extended) · sent every 10 ms
|
Byte |
Bit |
Length [bit] |
Signal |
Multiplier |
Offset |
Units |
Range / values |
|---|---|---|---|---|---|---|---|
|
1 |
0 |
2 |
Transmission Driveline Engaged (SPN 560) |
|
|
|
0 – Driveline Disengaged
|
|
1 |
2 |
2 |
Transmission Torque Converter Lockup Engaged (SPN 573) |
|
|
|
0 – Torque Converter Lockup Disengaged
|
|
1 |
4 |
2 |
Transmission Shift in Process (SPN 574) |
|
|
|
0 – Shift is Not in Process
|
|
1 |
6 |
2 |
Transmission Torque Converter Lockup Transition in Process (SPN 4816) |
|
|
|
0 – Transition is Not in Process
|
|
2 |
0 |
16 |
Transmission Output Shaft Speed (SPN 191) |
0.125 |
0 |
rpm |
0..8031.88 |
|
6 |
0 |
16 |
Transmission Input Shaft Speed (SPN 161) |
0.125 |
0 |
rpm |
0..8031.88 |
EEC2 Electronic Engine Controls
CAN ID 0x0CF00303 (29-bit extended) · sent every 50 ms
|
Byte |
Bit |
Length [bit] |
Signal |
Multiplier |
Offset |
Units |
Range / values |
|---|---|---|---|---|---|---|---|
|
2 |
0 |
8 |
Accelerator Pedal Position 1 (SPN 91) |
0.4 |
0 |
% |
0..100 |
|
5 |
0 |
8 |
Accelerator Pedal Position 2 (SPN 29) |
0.4 |
0 |
% |
0..100 |
EEC1 Electronic Engine Controls
CAN ID 0x0CF00403 (29-bit extended) · sent every 10 ms
|
Byte |
Bit |
Length [bit] |
Signal |
Multiplier |
Offset |
Units |
Range / values |
|---|---|---|---|---|---|---|---|
|
1 |
4 |
4 |
Actual Engine Percent Torque High Resolution (SPN 4154) |
0.125 |
0 |
% |
0..0.875 |
|
2 |
0 |
8 |
Driver's Demand Engine Percent Torque (SPN 512) |
1 |
-125 |
% |
-125..125 |
|
3 |
0 |
8 |
Actual Engine Percent Torque (SPN 513) |
1 |
-125 |
% |
-125..125 |
|
4 |
0 |
16 |
Engine Speed (SPN 190) |
0.125 |
0 |
rpm |
0..8031.88 |
|
8 |
0 |
8 |
Engine Demand Percent Torque 2 (SPN 2432) |
1 |
-125 |
% |
-125..125 |
ETC2 Electronic Transmission
CAN ID 0x18F00503 (29-bit extended) · sent every 100 ms
|
Byte |
Bit |
Length [bit] |
Signal |
Multiplier |
Offset |
Units |
Range / values |
|---|---|---|---|---|---|---|---|
|
1 |
0 |
8 |
Transmission Selected Gear (SPN 524) |
1 |
-125 |
|
-125..125 |
|
2 |
0 |
16 |
Transmission Actual Gear Ratio (SPN 526) |
0.001 |
0 |
|
0..64.255 |
|
4 |
0 |
8 |
Transmission Current Gear (SPN 523) |
1 |
-125 |
|
-125..125 |
|
5 |
0 |
16 |
Transmission Requested Range (SPN 162) |
|
|
|
Two ASCII characters. See the text values below. |
|
7 |
0 |
16 |
Transmission Current Range (SPN 163) |
|
|
|
Two ASCII characters. See the text values below. |
Transmission Requested Range and Current Range text values
Each field is two ASCII characters, the first in the lower-numbered byte. A single character is sent in the second position, with a space before it. Both fields are FF FF (not available) when the controller does not provide them.
Requested Range is the shift selector position.
Current Range is the same in automatic mode. In the other modes it is the mode letter and the selected gear.
|
Text |
Meaning |
|---|---|
|
" P" |
Park |
|
" R" |
Reverse |
|
" N" |
Neutral |
|
" D" |
Drive |
|
"D1", "D2", "D3", … |
Drive, held to that gear: the lever in a lower position, or range select on |
|
" I" |
Shift selector position not recognized |
|
"M" + gear |
Manual mode and the selected gear, for example "M3"; the gear is a digit, R or N |
|
"S" + gear |
Switch shift mode and the selected gear |
|
"T" + gear |
Diagnostic mode and the selected gear |
|
"F" + gear |
Failsafe and the selected gear |
ETC8 Electronic Transmission
CAN ID 0x18F00C03 (29-bit extended) · sent every 20 ms
|
Byte |
Bit |
Length [bit] |
Signal |
Multiplier |
Offset |
Units |
Range / values |
|---|---|---|---|---|---|---|---|
|
1 |
0 |
16 |
Transmission Torque Converter Ratio (SPN 3030) |
0.001 |
0 |
|
0..64.255 |
|
3 |
0 |
16 |
Transmission Clutch Converter Input Speed (SPN 5052) |
0.125 |
0 |
rpm |
0..8031.88 |
ACCS Acceleration Sensor
CAN ID 0x18F02D03 (29-bit extended) · sent every 10 ms
|
Byte |
Bit |
Length [bit] |
Signal |
Multiplier |
Offset |
Units |
Range / values |
|---|---|---|---|---|---|---|---|
|
1 |
0 |
16 |
Lateral Acceleration Extended Range (SPN 5347) |
0.01 |
-320 |
m/s^2 |
-320..322.55 |
|
3 |
0 |
16 |
Longitudinal Acceleration Extended Range (SPN 5348) |
0.01 |
-320 |
m/s^2 |
-320..322.55 |
|
5 |
0 |
16 |
Vertical Acceleration Extended Range (SPN 5349) |
0.01 |
-320 |
m/s^2 |
-320..322.55 |
TRF2 Transmission Fluids 2
CAN ID 0x18FD9503 (29-bit extended) · sent every 1000 ms
|
Byte |
Bit |
Length [bit] |
Signal |
Multiplier |
Offset |
Units |
Range / values |
|---|---|---|---|---|---|---|---|
|
1 |
4 |
2 |
Transmission Overheat Indicator (SPN 5345) |
|
|
|
0 – Transmission Overheat Indicator is Off
|
|
2 |
0 |
16 |
Transmission Torque Converter Oil Outlet Temperature (SPN 3823) |
0.03125 |
-273 |
deg C |
-273..1734.97 |
ETC7 Electronic Transmission
CAN ID 0x18FE4A03 (29-bit extended) · sent every 100 ms
|
Byte |
Bit |
Length [bit] |
Signal |
Multiplier |
Offset |
Units |
Range / values |
|---|---|---|---|---|---|---|---|
|
1 |
0 |
2 |
Transmission Current Range Display Blank State (SPN 4176) |
|
|
|
0 – Not Blanked
|
|
1 |
2 |
2 |
Transmission Service Indicator (SPN 4178) |
|
|
|
0 – Transmission Service Indicator is Off
|
|
1 |
4 |
2 |
Transmission Requested Range Display Blank State (SPN 1850) |
|
|
|
0 – Inactive; Transmission Requested Range display should NOT be blanked
|
|
1 |
6 |
2 |
Transmission Requested Range Display Flash State (SPN 1849) |
|
|
|
0 – Inactive; Transmission Requested Range display should NOT be flashing
|
|
2 |
2 |
2 |
Active Shift Console Indicator (SPN 2945) |
|
|
|
0 – Primary Shift Console is Active
|
|
2 |
4 |
2 |
Transmission Engine Crank Enable (SPN 2900) |
|
|
|
0 – Cranking Disabled; engine cranking is prohibited by the transmission
|
|
2 |
6 |
2 |
Transmission Shift Inhibit Indicator (SPN 1851) |
|
|
|
0 – Inactive; shift is not inhibited
|
|
3 |
0 |
2 |
Transmission Mode 4 Indicator (SPN 2539) |
|
|
|
0 – Transmission Mode 4 Not Active
|
|
3 |
2 |
2 |
Transmission Mode 3 Indicator (SPN 2538) |
|
|
|
0 – Transmission Mode 3 Not Active
|
|
3 |
4 |
2 |
Transmission Mode 2 Indicator (SPN 2537) |
|
|
|
0 – Transmission Mode 2 Not Active
|
|
3 |
6 |
2 |
Transmission Mode 1 Indicator (SPN 2536) |
|
|
|
0 – Transmission Mode 1 Not Active
|
|
4 |
0 |
8 |
Transmission Requested Gear Feedback (SPN 3289) |
1 |
-125 |
|
-125..125 |
|
5 |
0 |
2 |
Transmission Mode 5 Indicator (SPN 4250) |
|
|
|
0 – Disable
|
|
5 |
2 |
2 |
Transmission Mode 6 Indicator (SPN 4251) |
|
|
|
0 – Disable
|
|
5 |
4 |
2 |
Transmission Mode 7 Indicator (SPN 4252) |
|
|
|
0 – Disable
|
|
5 |
6 |
2 |
Transmission Mode 8 Indicator (SPN 4253) |
|
|
|
0 – Disable
|
|
6 |
0 |
2 |
Transmission Reverse Gear Shift Inhibit Status (SPN 4261) |
|
|
|
0 – Reverse Gear Shifts are Currently Allowed
|
|
6 |
2 |
2 |
Transmission Warning Indicator (SPN 5344) |
|
|
|
0 – Transmission Warning Indicator is Off
|
VEP2 Vehicle Electrical Power
CAN ID 0x18FE8D03 (29-bit extended) · sent every 1000 ms
|
Byte |
Bit |
Length [bit] |
Signal |
Multiplier |
Offset |
Units |
Range / values |
|---|---|---|---|---|---|---|---|
|
1 |
0 |
16 |
Battery Potential Power Input 2 (SPN 444) |
0.05 |
0 |
V |
0..3212.75 |
|
3 |
0 |
16 |
ECU Power Output Supply Voltage 1 (SPN 3597) |
0.05 |
0 |
V |
0..3212.75 |
|
5 |
0 |
16 |
ECU Power Output Supply Voltage 2 (SPN 3598) |
0.05 |
0 |
V |
0..3212.75 |
|
7 |
0 |
16 |
ECU Power Output Supply Voltage 3 (SPN 3599) |
0.05 |
0 |
V |
0..3212.75 |
ET2 Engine Temperature 2
CAN ID 0x18FEA403 (29-bit extended) · sent every 1000 ms
|
Byte |
Bit |
Length [bit] |
Signal |
Multiplier |
Offset |
Units |
Range / values |
|---|---|---|---|---|---|---|---|
|
3 |
0 |
16 |
ECU Temperature (SPN 1136) |
0.03125 |
-273 |
deg C |
-273..1734.97 |
ETC6 Electronic Transmission
CAN ID 0x18FEAB03 (29-bit extended) · sent on 50ms
|
Byte |
Bit |
Length [bit] |
Signal |
Multiplier |
Offset |
Units |
Range / values |
|---|---|---|---|---|---|---|---|
|
1 |
0 |
8 |
Recommended Gear (SPN 1113) |
1 |
-125 |
|
-125..125 |
|
2 |
0 |
8 |
Highest Possible Gear (SPN 1115) |
1 |
-125 |
|
-125..125 |
|
3 |
0 |
8 |
Lowest Possible Gear (SPN 1114) |
1 |
-125 |
|
-125..125 |
DM1 Active Diagnostic Trouble Codes
CAN ID 0x18FECA03 (29-bit extended) · sent every 1000 ms
|
Byte |
Bit |
Length [bit] |
Signal |
Multiplier |
Offset |
Units |
Range / values |
|---|---|---|---|---|---|---|---|
|
1 |
0 |
2 |
Protect Lamp (SPN 987) |
|
|
|
0 – Lamp Off
|
|
1 |
2 |
2 |
Amber Warning Lamp (SPN 624) |
|
|
|
0 – Lamp Off
|
|
1 |
4 |
2 |
Red Stop Lamp (SPN 623) |
|
|
|
0 – Lamp Off
|
ET1 Engine Temperature 1
CAN ID 0x18FEEE00 (29-bit extended) · sent every 1000 ms
|
Byte |
Bit |
Length [bit] |
Signal |
Multiplier |
Offset |
Units |
Range / values |
|---|---|---|---|---|---|---|---|
|
1 |
0 |
8 |
Engine Coolant Temperature (SPN 110) |
1 |
-40 |
deg C |
-40..210 |
CCVS1 Cruise Control Vehicle
CAN ID 0x18FEF103 (29-bit extended) · sent every 100 ms
|
Byte |
Bit |
Length [bit] |
Signal |
Multiplier |
Offset |
Units |
Range / values |
|---|---|---|---|---|---|---|---|
|
2 |
0 |
16 |
Wheel Based Vehicle Speed (SPN 84) |
0.00390625 |
0 |
km/h |
0..250.996 |
|
4 |
4 |
2 |
Brake Switch (SPN 597) |
|
|
|
0 – Brake pedal released
|
TRF1 Transmission Fluids 1
CAN ID 0x18FEF803 (29-bit extended) · sent every 1000 ms
|
Byte |
Bit |
Length [bit] |
Signal |
Multiplier |
Offset |
Units |
Range / values |
|---|---|---|---|---|---|---|---|
|
1 |
0 |
8 |
Clutch Pressure (SPN 123) |
16 |
0 |
kPa |
0..4000 |
|
2 |
0 |
8 |
Transmission Oil Level 1 (SPN 124) |
0.4 |
0 |
% |
0..100 |
|
4 |
0 |
8 |
Transmission Oil Pressure (SPN 127) |
16 |
0 |
kPa |
0..4000 |
|
5 |
0 |
16 |
Transmission Oil Temperature 1 (SPN 177) |
0.03125 |
-273 |
deg C |
-273..1734.97 |
|
7 |
0 |
8 |
Transmission Oil Level 1 High Low (SPN 3027) |
0.5 |
-62.5 |
L |
-62.5..62.5 |
|
8 |
0 |
4 |
Transmission Oil Level 1 Countdown Timer (SPN 3028) |
|
|
|
See the value table below. |
|
8 |
4 |
4 |
Transmission Oil Level 1 Measurement Status (SPN 3026) |
|
|
|
See the value table below. |
Transmission Oil Level 1 Countdown Timer
|
Value |
Meaning |
|---|---|
|
0 |
Less than 1 Minute |
|
1 |
One Minute |
|
2 |
Two Minutes |
|
3 |
Three Minutes |
|
4 |
Four Minutes |
|
5 |
Five Minutes |
|
6 |
Six Minutes |
|
7 |
Seven Minutes |
|
8 |
Eight Minutes |
|
9 |
Nine Minutes |
|
10 |
Ten Minutes |
|
11 |
Eleven Minutes |
|
12 |
Twelve Minutes |
|
13 |
Thirteen Minutes |
|
14 |
Error |
|
15 |
Not Available |
Transmission Oil Level 1 Measurement Status
|
Value |
Meaning |
|---|---|
|
0 |
Conditions Valid for Transmission Oil Level Measurement |
|
1 |
Conditions Not Valid - Setting Timer Still Counting Down |
|
2 |
Conditions Not Valid - Transmission in Gear |
|
3 |
Conditions Not Valid - Transmission Fluid Temperature Too Low |
|
4 |
Conditions Not Valid - Transmission Fluid Temperature Too High |
|
5 |
Conditions Not Valid - Vehicle Moving; Output Shaft Speed Too High |
|
6 |
Conditions Not Valid - Vehicle Not Level |
|
7 |
Conditions Not Valid - Engine Speed Too Low |
|
8 |
Conditions Not Valid - Engine Speed Too High |
|
9 |
Conditions Not Valid - No Request for Reading |
|
10 |
Not Defined |
|
11 |
Not Defined |
|
12 |
Not Defined |
|
13 |
Conditions Not Valid - Other |
|
14 |
Error |
|
15 |
Not Available |
DBC File
Related Articles
- Connectors Used In CAN Networks
- Connecting COMPUSHIFT to Holley Sniper EFI or Holley TerminatorX
- Connecting COMPUSHIFT to Holley EFI / Racepak
- HGM CAN Bus Messaging
- Connecting COMPUSHIFT to AEM ECU's
- Connecting COMPUSHIFT to Emtron
- Connecting COMPUSHIFT to Cummins R2.8 CM2220
- Connecting COMPUSHIFT to Chrysler HEMI Crate Engine
- Adding an ECU to a CAN Bus Network
- Connecting COMPUSHIFT to Edelbrock ProFlo 4
- Connecting COMPUSHIFT to Haltech Elite or Haltech Platinum
- Connecting COMPUSHIFT to Megasquirt
- Using and Working with CAN Bus
- Connecting COMPUSHIFT to Link G4+ ECU
- Connecting COMPUSHIFT to J1939 Engine Management